Storing kinetic energy in a flywheel allows for more efficient driving of electricvehicles. Research in this area is in progress at Uppsala University, where a flywheelwith magnetic bearings encased in a vacuum chamber is being constructed. To makethis possible methods for measuring the current through the electromagnets in thebearings and temperatures in the flywheel need to be developed. This has been thepurpose of this report. The current measurement resulted in a resistive method, andthe implementation of eight measurement circuits in the system.

This master thesis investigates quality procedures and measuring of solid carbide end mills, with the main focus on measuring equipment. The thesis has been written in collaboration with a special production department for solid carbide end mills at Sandvik Coromant in Gimo. The department?s needs and constraints have been the foundation of the project and the main research question is: how to measure end mills in order to ensure good quality of the produced end mills. The project has contained both a theoretical study consisting of a literature review and practical studies in the workshop with the objective to identify an end mill?s main parameters and the relationship between an end mill?s geometry and the manufacturing processes.

A discussion regarding the alignment and measuring procedure of propeller shafts has arose due to the competing situation in the industry, and higher standards from the customers. An estimation of the deflection of shafts in different alignment situations has been made with help of FEM-analysis and beam theory. This has been analyzed and compared with the experience from Rolls-Royce AB suppliers of shafts. An evaluation of measuring protocols has been made and the result indicates that there is a correlation between the deflection of the shaft and the run out. Results from a measuring test performed by Balino, Spain, verifies this conclusion.

A discussion regarding the alignment and measuring procedure of propeller shafts has arose due to the competing situation in the industry, and higher standards from the customers. An estimation of the deflection of shafts in different alignment situations has been made with help of FEM-analysis and beam theory. This has been analyzed and compared with the experience from Rolls-Royce AB suppliers of shafts. An evaluation of measuring protocols has been made and the result indicates that there is a correlation between the deflection of the shaft and the run out. Results from a measuring test performed by Balino, Spain, verifies this conclusion.

The report describes a measuring method for analysis of energy consumption measurement in microwave ovens. Concurrently that the awareness of the environment evolves the demands are growing for more power saving products. This is also counting within the Home Appliance business, which is Whirlpools business area. Whirlpool is therefore interested of launching microwave ovens with documented low power consumption. To be able to implement this, both asserted measuring equipment, that fulfils all demands, and a standard procedure is required.

There are no reliable, objective and simple methods today for measuring pain in horses. The purpose of this study was to evaluate and describe measuring of mechanical nociceptive threshold (MNT) values with a pressure algometer in clinically pain free riding horses at the riding school of Strömsholm. In this study there were 24 horses. Tape recording and electromyelografi (EMG) was used in an attempt to increase objectivity in the examination. MNT increased with age, however sex and colour had no influence.

The project contains a force analysis of the vertical axis wind turbine Lucia's supporting arms and a measuring device to experimentally measure the forces is made. The forces between the supporting arms and the tower are calculated theoretically and then simulated by a computere. A measuring devise is then designed to measure the forces experimentally. The forces acting on the attachment between the supporting arms and the tower is primarily the centripetal force, gravitational force and the aerodynamic forces on the rotor wings. The maximum forces were theoretically calculated and is 13.38 kN along the x-axis, -0.25 kN along the y-axis and then 0.5 kN along the z-axis.

Problem: In society of today corporate competence is an important factor for survivor and development. IT is developing rapidly and can not be ignored by companies. Then need for people with IT-competence is conquent increasing. A survey of corporate IT-competence is therefore of interest for companies as well as for local authorities. To determine the IT competence within an organisation, this competence has to be measurable.

Problem: In society of today corporate competence is an important factor for survivor and development. IT is developing rapidly and can not be ignored by companies. Then need for people with IT-competence is conquent increasing. A survey of corporate IT-competence is therefore of interest for companies as well as for local authorities. To determine the IT competence within an organisation, this competence has to be measurable.

Normally the operational amplifier is used as a component in active filter design. The goal for future components in filter design is large bandwith and the use of low supply voltages. The use of current-mode instead of voltage-mode circuits gets a step closer to the required performance. A component that use current as the signal conveying part is the current conveyor. In this report a comparative study between two current conveyor structures of second generation (CCII) is performed.

Energimätning och övervakning kan bidra till minskad energiförbrukning genom att hjälpa en användare att ta beslut över energianvändandet. Valet av examensarbete gjordes p.g.a. behovet att ge användarna möjlighet att påverka sin energiförbrukning och övervaka sina elprodukter. Ett koncept togs fram där toppvärden på spänning och ström, effektfaktor, spänning-ens vågform, aktiv, reaktiv och skenbar effekt mättes. Samtliga värden skickades till en server som lagrade informationen och innehöll en hem-sida för presentation.

The purpose of this study has been to investigate advantages and problems with distributionsystem metering in substations. This report is a study in cooperation with Göteborg Energi.The analyses in this report are made for GENAB, a subsidiary company of Göteborg Energi.To analyse advantages and problems in advance is interesting information for GENAB. Theresult of the report could be based upon whether installation of metering in distributionsubstations will be implemented and in that case which kind of measurement that is relevant.The most relevant and strategic place to implement measurement is at the distributionsubstations on the secondary side (400V), this is due to the placement of the currenttransformers. The measurements in this study involve current, voltage, power, power factor,temperature, energy and power quality.Measuring instruments that are relevant to implement are intended to measure current,voltage, power, power factor, energy and, possibly, power quality in the same measuring unit.It is desirable to have a measuring instrument that measures both energy and power qualitybut since it is most often a cost question, it can be established that energy meters have a lowercost.Metering in distribution substations gives a better illustration of the power network. Thisresults in many advantages for GENAB.

This thesis is a study of humidity at Knauf Danogips external plasterboard. The study is performed at the building project Kv. Maskinen in Jönköping in cooperation with NCC Construction AB and Knauf Danogips. The measuring was performed during five winter/spring months to see how the weather influenced the plasterboard.The measuring was performed at a small two-storied building and a larger fourstoried building. From the buildings` placement were a couple of measuring dots selected and to get a good result was the dots located in the four cardinal points.

The assignment is issued by Scania Maintence AB seeking a new approach to detect power changes in their industrial processes. The work has taken place at Ångströmslaboratoriet and tests have been performed at Scania AB Södertälje.Today?s society consumes enormous amount of energy. In both economically and environmental view, it is important that the processes are effective, with high power factor. There are many ways to measure power in the industry, what they all have in common is that the installation is advanced, requires time and planning.

Strong relationships are something that is really important for companies to succeed with, in purpose to increase and protect their market shares. After major research on the subject, it has been found that variables like exchange of relationship, trust, control mutability, satisfaction and commitment are important in the establishment of measuring a relationship. The purpose with this thesis was to: increase the knowledge on how companies measure, and then consequently evaluate, their relationships. To answer the purpose of the study we chose to do a case study at Stadium AB, which is a retailing concern with a high level of customer contact on a daily basis. The conclusion is that trust most likely is the key variable in measuring relationships.